Protection and security against damage and unauthorized access. You should also gather together all of the cards you plan to install, as well as the keyboard you plan toĪ lockable door is located on the chassis front cover, providing access to the control panel. Setting up your IPC-610 requires only a screwdriver and a small amount of time. Shock (operating): 10 g acceleration peak (11 ms duration).Vibration (operating): 5 ~ 17 Hz, 0.1" double amplitude displacement 17 ~ 500 Hz, 1.5 g.Relative humidity: 10 ~ 95% 40° C, non-condensing.Indicators: LEDs for power on/off, HDD and keyboard-lock.Controls: Reset, power on/off and keyboard-lock switches.Keyboard connector: Pre-wired DIN connectors on both front and rear panels.Cooling system: One 32 CFM cooling fan (flow-out) on the rear panel for the power supply, anotherĨ6 CFM fan (flow-in) on the front panel with an air filter.Disk drive capacity: Two half-height 5¼" drives and one 3½" drive accessible from the front panel.The IPC-610-XXX-300R is designed to use the popular 300 Wįor more detailed information, contact your local dealer.
The IPC-610-XXX-250X is designed to use the popular "ATX" 250 W Inexpensive "Baby AT” and "ATX" form-factor motherboards. The IPC-610-MB-XXX is designed to use the popular and
There are several special versions of the IPC-610 also available. A lockable door protects drives and switches from tampering and foreign The chassis is positively pressurized by two filtered push-pull cooling fans toĮxclude dust and dirt. The IPC-610 will withstand shock, vibration, dust, and a wide range of operating temperatures in harsh They can be conveniently installed and replaced The IPC-610 accommodates most plug-in cards, includingĬPU, video, disk controller, and I/O interface cards. Modular in design and can be easily serviced. Makes upgrading easier and allows for a more efficient system package. The passive backplane configuration of the IPC-610 minimizes downtime, simplifies troubleshooting, Passive backplane, and a more efficient switching power supply in a single fan-cooled chassis. The unit includes a 14-slot PC-bus compatible This rugged, all-steelĬhassis meets the EIA RS-310C 19" rackmount standard. The IPC-610 is a PC/AT-compatible computer designed for industrial applications. 11įigure B-3: IPC-610 exploded diagram (speaker, LED, fan). 10įigure B-2: IPC-610 exploded diagram (case components). 9įigure B-1: IPC-610 exploded diagram (internal components). 9įigure A-5: IPC-610 ATX chassis component layout. 8įigure A-4: Rear window of IPC-610 for standard AT motherboard. 7įigure A-3: Rear window of IPC-610 for standard 14-slot backplane, with PS/2 size power supply. 6įigure A-1: IPC-610 with PS/2 size power supply.
6įigure A-2: IPC-610 with redundant power supply. 6Ī.1 Changing the Rear Cover According to Power Supply Used. 4įigure 2-5: Inserting the rubber buffers. 4įigure 2-4: Detaching the hold-down clamp. 3įigure 2-3: Inserting the drives into the drive bay. This manual is subject to changeħth Edition Printed in Taiwan September 1998Ĭhapter 1 General Information. Information or products described herein. does not assume any liability arising out of the application or use of the The information in this document is provided for reference only. assumes no responsibility for its use, nor for any infringements of the rights of third parties which may result from its use. Manual is intended to be accurate and reliable. Means without the prior written permission of Advantech Co., Ltd. No part of this manual may be reproduced, copied, translated or transmitted in any form or by any reserves the right to make improvements to the products described in this manual All rights are reserved.Īdvantech Co., Ltd. This document is copyrighted, September 1998, by Advantech Co., Ltd.
0 kommentar(er)
